One reason as to why most consumers, manufacturers, and business persons are considering the use of powder coating technique is to produce products that are not only attractive but also functional. Besides extending the lifespan of products, it also boosts the appearance of the same. Since it is unwise to entrust the coat application work to anyone, consider a reputable powder coating Hickory NC contractor.
To coat a surface, there has to be some procedures that have to be followed stringently. Applying a coat over a metal substrate by use of electrostatic charge technique requires the right skill. Before anything is done on the substrate material, it has to be pre-treated by cleaning it properly. This is usually for purposes of expelling all the dirt, dust, and debris attached to surfaces.
The surface pre-treatment may be done using chemicals or sandblasting procedures in order to ensure that the substrate is absolutely clean. After treating the surface, it is now time to dry the substrate. This is usually done for about 20 to 30 minutes. Until the surface has completely dried, the powdered material should not be applied.
The coat might not adhere well in moist surfaces because it could create pockets of air within the film. More often than not, contamination of dust and other powder coloration may occur. This may occur especially when the area is dirty. Caution should be taken to ensure that the coating is applied in a clean surface. Heating the powder is done till it reaches the desired melting point.
The next task to do is to heat the powder until it reaches its melting point. This is in order to allow it to flow over the surface and create uniform finish. Whenever the coat is uniform, it enables the surface to be adamant to any form of damage. At temperatures of about 400 degrees, a complete cure happens. You may be asking yourself why it is important to powder coat your appliances.
One of the greatest merits of powdered coat is that it results to the formation of hard finishes, which are usually tougher than conventional paints. The hard finish formed guarantees more durable coat that is greatly resistant to moisture, chemicals, chipping, abrasions, corrosion, fading, wear and tear, as well as other extreme and unfavorable weather conditions.
Additionally, powdered coats are available in a wide spectrum of colors. The attractive finishes that you see around on kitchen appliances or your lawn mowers are probably powder coated. An experienced contractor is able determine the kind of coat to apply. In case the texture of the surface is rough, the coating should also be rough and vise versa.
Metal particle coats should be applied in such a way that they contain no bubbles or even sags. They should be strong and durable. More so, they should be resistant to abrasion, cracking, and even peeling on the extreme. Whether it is your bicycle, building material, kitchen appliances, hardening tools, or industrial equipments, you can have them coated to enhance their durability and prevent environmental and man-made factors from causing damages.
To coat a surface, there has to be some procedures that have to be followed stringently. Applying a coat over a metal substrate by use of electrostatic charge technique requires the right skill. Before anything is done on the substrate material, it has to be pre-treated by cleaning it properly. This is usually for purposes of expelling all the dirt, dust, and debris attached to surfaces.
The surface pre-treatment may be done using chemicals or sandblasting procedures in order to ensure that the substrate is absolutely clean. After treating the surface, it is now time to dry the substrate. This is usually done for about 20 to 30 minutes. Until the surface has completely dried, the powdered material should not be applied.
The coat might not adhere well in moist surfaces because it could create pockets of air within the film. More often than not, contamination of dust and other powder coloration may occur. This may occur especially when the area is dirty. Caution should be taken to ensure that the coating is applied in a clean surface. Heating the powder is done till it reaches the desired melting point.
The next task to do is to heat the powder until it reaches its melting point. This is in order to allow it to flow over the surface and create uniform finish. Whenever the coat is uniform, it enables the surface to be adamant to any form of damage. At temperatures of about 400 degrees, a complete cure happens. You may be asking yourself why it is important to powder coat your appliances.
One of the greatest merits of powdered coat is that it results to the formation of hard finishes, which are usually tougher than conventional paints. The hard finish formed guarantees more durable coat that is greatly resistant to moisture, chemicals, chipping, abrasions, corrosion, fading, wear and tear, as well as other extreme and unfavorable weather conditions.
Additionally, powdered coats are available in a wide spectrum of colors. The attractive finishes that you see around on kitchen appliances or your lawn mowers are probably powder coated. An experienced contractor is able determine the kind of coat to apply. In case the texture of the surface is rough, the coating should also be rough and vise versa.
Metal particle coats should be applied in such a way that they contain no bubbles or even sags. They should be strong and durable. More so, they should be resistant to abrasion, cracking, and even peeling on the extreme. Whether it is your bicycle, building material, kitchen appliances, hardening tools, or industrial equipments, you can have them coated to enhance their durability and prevent environmental and man-made factors from causing damages.
About the Author:
When you have the need for powder coating Hickory NC finishing company is at your service and can be reached quickly. To get a quote, click on the source http://www.diversifiedfinishers.com.
No comments:
Post a Comment